Kb-electronics KBPC-225D Manual de usuario descargar pdf

“The Right Control for Your Application.” 12095 NW 39 Street, Coral Springs, FL 33065-2516

Telephone: 954-346-4900; Fax: 954-346-3377

KB Electronics, Inc. www.kbelectronics.com

INSTALLATION AND OPERATION MANUAL SUPPLEMENT

KBPC-225 (PART NOS. 9391 & 9392)

(A42114) – Rev. C – 10/11/2011 Page 1 of 2

This supplement is for Model KBPC-225D and is supplied with the KBPC-225 Installation and Operation Manual (Part No. A40350) until the

new manual is available. The manual must be read and understood before operating this drive. For further assistance, contact our Sales

Department at 954-346-4900 or Toll Free at 800-221-6570 (outside Florida).

DESCRIPTION OF PRODUCT UPDATES

● The drive accepts 115 and 208/230 Volt AC Line Input with the setting of both Jumpers J2A and J2B (115V, 230V)

● The drive can be used with 180 and 90 Volt DC motors with the setting of Jumper J3 (180V, 90V).

● A Run Relay has been added, with the output contacts at TB4, which can be used to turn equipment "on" or "off" as a function of drive status

(Off, Stop, Run).

● All trimpots have been moved and aligned at the top of the PC board.

● The drive has been converted to Surface Mount Technology (SMT).

See Figure 4, on other side, for location of Jumpers, Run Relay Output Contacts, and Trimpots (replaces Figure 1, on page 5, in the manual).

Notes: 1. The Schematic (Figure 12, on page 15) and Parts List (Table 4, on page 16) in the manual no longer apply to this drive and should

not be used. 2. The PC board references the motor terminals of Terminal Block TB1 as "A+" and "A-" (the manual references these terminals

as "A1" and "A2") and the field terminals of Terminal Block TB2 as "F+" and "F-" (the manual references these terminals as "F1" and "F2").

DUAL VOLTAGE INPUT SELECTION (JUMPERS J2A and J2B)

Provide selection of AC Line Input voltage (115V, 230V).

See Figure 1.

208/230 Volt AC Line Input: Set both Jumpers J2A and J2B to the "230V"

position (factory setting).

115 Volt AC Line Input: Set both Jumpers J2A and J2B to the "115V"

position.

MOTOR VOLTAGE SELECTION (JUMPER J3) OR

TACH-GENERATOR FEEDBACK SELECTION

(JUMPERS J3 AND J6)

Provides selection of motor voltage (180V, 90V) or tach-

generator feedback voltage (7V, 20/30V, 50V).

180 Volt DC Motors: Set Jumper J3 to the "180V" position

(factory setting).

See Figure 2.

90 Volt DC Motors: Set Jumper J3 to the "90V" position.

See Figure 2.

Step-Down Operation: Set Jumper J3 to the "90V" position

for 90 Volt DC Motors with 208/230Volt AC Line input (with

both Jumpers J2A and J2B set to the "230V" position).

See Figure 2.

Tach-Generator Feedback: With a tach-generator

connected to Terminal block TB3, set Jumper J3 to the "T"

position and set Jumper J6 to the corresponding tach-

generator voltage (factory set to "7V").

See Figure 3.

Note: If tach-generator feedback is not required, the position of Jumper J3 does not matter.

FIGURE 1

AC LINE INPUT VOLTAGE SELECTION

(JUMPERS J2A AND J2B)

208/230 Volt AC Line Input

(J2A and J2B Set to "230V")

(Factory Setting)

115 Volt AC Line Input

(J2A and J2B Set to "115V")

FIGURE 2

MOTOR VOLTAGE SELECTION

(JUMPER J3)

FIGURE 3

TACH-GENERATOR FEEDBACK

(JUMPERS J3 AND J6)

180 Volt Motors

(J3 Set to "180V")

(Factory Setting)

90 Volt Motors*

(J3 Set to "90V")

(J3 Set to "T")

(J6 Set to Tach-Generator Voltage)

*Use "90V" setting for Step-Down

Operation (90 Volt DC Motors with

208/230 Volt AC Line input).

1 2 3 4 5 6 ... 18 19

Indice de contenidos

Pagina 1

“The Right Control for Your Application.” 12095 NW 39 Street, Coral Springs, FL 33065-2516 Telephone: 954-346-4900; Fax: 954-346-3377 KB Electr

Pagina 2

8FIG. 4A – CAPTIVE SCREWTIGHTENED IN CASECAPTIVE SCREWCOVERGASKETCASEFIG. 4B – CAPTIVE SCREW ENGAGEDIN FRONT COVERGASKETCOVERCASECAPTIVE SCREWV. WIRIN

Pagina 3 - KBPC-225

9FIG. 6A – FULL VOLTAGE FIELD180 VDC MOTORS WITH 200 VDC FIELDS+A1F2A2 L1 L2FIELDTB1TB2ACLINEARMF1––+FIG. 6B – HALF VOLTAGE FIELD180 VDC MOTORS WITH 1

Pagina 4

10FIG. 8A – REMOTE POTENTIOMETERCONNECTIONP1P2P3FIG. 8B – ANALOG VOLTAGE CONNECTIONG. Remote Start/Stop Switch – A remote Start/Stop Switch can be ins

Pagina 5 - P/N 9431 or equivalent)

11VII. OPERATION.WARNING! Read Safety Warning on page 3 before attempting to operate thecontrol or severe injury or death can result.After the contro

Pagina 6

12E. Current Limit (CL) – This trimpot is used to set the maximum amount of DC current thatthe motor can draw. The amount of DC current determines th

Pagina 7 - FIG. 1 – CONTROL LAYOUT

132. Motor may be defective - check motor for shorts or grounds.3. The CL may be set too low - check position of CL trimpot.NOTE: In some application

Pagina 8 - LED LIGHTS

INCHES [mm]FIG. 11 – MECHANICAL SPECIFICATIONS14TMTM

Pagina 9

FIG. 13 – INTERNAL CONNECTION DIAGRAM15

Pagina 10 - 230 100 F1, L1 Half Voltage

FIG. 14 – CONNECTION DIAGRAMS1612345678910KBSI-240D KBPC-225P2P1L1 L212345678910SIGNAL FOLLOWINGAUTOMATIC MODESIGNAL FOLLOWINGAUTOMATIC MODEWITH MANUA

Pagina 11

XI. – LIMITED WARRANTYFor a period of 18 months from date of original purchase, KB will repair or replace withoutcharge devices which our examination

Pagina 12

“The Right Control for Your Application.” 12095 NW 39 Street, Coral Springs, FL 33065-2516 Telephone: 954-346-4900; Fax: 954-346-3377 KB Electr

Pagina 13

Pagina 14

2TABLE OF CONTENTSSection Pagei. Safety Warning ...3ii. Simplified Operating Instructions ...

Pagina 15

3 i. SAFETY WARNING! — PLEASE READ CAREFULLYThis product should be installed and serviced by a qualified technician, electrician orelectric

Pagina 16

4The electronics for the KBPC is state-of-the-art and includes short circuit and transientprotection which provides the ultimate in reliability. Elec

Pagina 17

5FIG. 1 – CONTROL LAYOUTIllustrates Approximate Factory Setting of Jumpers and TrimpotsMAXMINDWG#: B2800-1-00890KBPCGND(EARTH)COMI1I2JOGP3P2P1TB3T+T-J

Pagina 18 - TERMINAL

6II. SETTING SPEED OR TORQUE MODE OF DRIVE (JUMPER J1)A. Speed Control Mode – When Jumper J1 is placed in the "SPD" position the drive willc

Pagina 19 - 1/10/96 Rev. A (A40350)

7B. J5 - Current Limit Mode – (Factory set for "TCL") This control contains electronic currentlimiting which limits the maximum DC current t

Comentarios a estos manuales

Sin comentarios

Kb-electronics KBPC-225D Manual de usuario

Busca en linea o descarga Manual de usuario para Software Kb-electronics KBPC-225D. KB Electronics KBPC-225D User Manual [fr] Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Software Kb-electronics KBPC-225D